Assembly instructions © 2008 PRODUCT GUIDEMODEL 463271309© 2008 Char-Broil, LLC Columbus, GA 31902Printed in China Serial NumberDate Purchase
This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this pr
PARTS LISTNOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the
PARTS DIAGRAM12QQBCDDACEFGHIJKLMNOPQRSTUVWXYYZZAABBCCDDEEFFAAABBBGGHHIIJJKKLLMMNNOOOOPPRRSSSSTTUUV VWWXXYYZZ
ASSEMBLY21/4-20x1/2” screw1Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel.IMPORTA
34This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of g
Upper back panel651/4-20x1½”screw7mm lockwasher7mm flatwasher 15On back of grill, place upper back panel between side panels and above lower back pan
716Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A.Attach rear of shelf using one1/4-20x3/4” screw, 7
8Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using
8a111018#10-24x3/8” screwSideburner lidPlace sideburner lid onto left shelf and align holes in back of lid with hinge holes. Secure lid to hinges usin
12B13A 19 Place sideburner grate onto sidebruner shelf..Inside of cart, insert rear heat shield tabs(without holes) into three slots between upper an
1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.2. An LP cylinder not connected fo
1415Inside of cart, insert end of tank wire (without hole) into back of lower back panel. end of tank wire Attach other end to bottom of front brace w
1617 21Release the cap and nut from electronic ignition module. Attach electronic ignition module and heat shield to the cart rightInsert AA battery
19Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox.22 Fl
2123On back of grill, slide grease tray into opening in upper back panel.CAUTIONFailure to install grease tray will cause hot grease to drip from bott
22LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.EmergenciesProblemGas leaking from cracked
Troubleshooting (continued)ProblemBurner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also)Burner(s) will notmatch light.
Troubleshooting - Electronic IgnitionProblem (Ignition)SECTION INo sparks appear at any electrodes when control knob turned to ; no noise ca
29
WARNINGCALIFORNIA PROPOSITION 651. Combustion by-products produced when using this product contain chemicals known to the State of California to cause
REGTEMP REV0031
OPD Hand WheelLP (Liquefied Petroleum Gas)•LP gas is nontoxic, odorless and colorless when produced. For Your Safety, LP gas has been given an odor (s
WARNINGIf “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department!Connecting Regulator to the
6.Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in
WARNINGFor Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from
Burner Flame Check•Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW positio
Cleaning the Burner AssemblyFollow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn g
Comments to this Manuals