T-47DAssembly instructions © 2011 PRODUCT GUIDEMODEL 463251012© 2011 Char-Broil, LLC Columbus, GA 31902Printed in China Serial NumberDate Pur
This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this pr
PARTS LISTNOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the
PARTS DIAGRAM12ACPPDCMMMZXUVYIIZZAAAERQQSSTTUURRHPOOLLAANNIJNWWXXYYFFKKLLSHHIIIIIIHHBBEEEECCDDDDTGGOQQVVWJJJKKGBBBBF
ASSEMBLY21/4-20x1/2” screw1Attach side panels to bottom shelf using three 1/4-20x1/2” screws per panel. IMPORTANT: Panel with large hole mustBe on Rig
3Place lower back panel between side panels at rear of bottom shelf, oriented as shown. Secure lower back panel to sidepanels using two 1/4-20x1/2” sc
45Attach center cart divider to bottom shelf using three #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. 15On back of grill, attach cente
67Attach cabinet shelf to center cart divider using two #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. Attach cabinet shelf to cart left s
89ABInsert front brace between cart side panels. Orient the front brace with the door hinge pin on the top right side. Secure using one 1/4-20x1½” scr
10This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of g
12 1913Inside of the cart, connect the wires from burner electrodes into the back of Electronic Ignition module. Total (5) connections.Note: Switch te
1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.2. An LP cylinder not connected fo
1420Attach right side shelf to firebox using two 1/4-20x3/4” screws and 1/4” nuts, shown A.Attach front of shelf using two #8x3/8” self-tapping screws
1521ACDLeft side control panelLeft side shelfLeft side shelfLeft side shelfSide burner lidAttach left side control panel to left side shelf using four
16A 221/4-20x1½” 1/4-20x3/4” screw 1/4” nutAttach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown B. Attach rear
8a1823Insert sideburner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on shelf, shown A. Make sure bu
2024pinon bottomof doorTop ofdoorPRESSRight doorInsert the pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, alig
22Attach left small doors to left side panel using eight #8-32x1/4” screws. 2521#8-32x1/4” screwTroughsTrough middle bracketPut trough middle brack
2426Place cooking grates onto firebox as shown.Insert the four wire ends at rear of warming rack into holes in back of fire box. Front wires of warmin
1Main Burner ConversionYour grill may differ from illustration shown. This portion of the manual covers a variety of grill styles. Use pictures as r
4BezelsValveStemScrewsMain Burner Control KnobsNatural Gas Bezel80007893Pull the Burner Control Knobs off of Valve Stems.Remove Screws and Washers tha
6 7Open Sideburner lid and remove the Sideburner Grate.Beneath Sideburner shelf, remove Wingnut.Remove Sideburner from shelf.WingnutSideburner GrateOr
WARNINGCALIFORNIA PROPOSITION 651. Combustion by-products produced when using this product contain chemicals known to the State of California to cause
89Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and Washers securing Bezel to shelf control
11 Using the provided Orifice Removal Tool, unscrew the Orifice from the end of the Sideburner Valve. Save removed Orifice and Orifice Removal Tool f
1213Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and Washers securingBezel to shelf contro
14Natural Gas Hose Conversion Using a wrench, not provided, remove LP Regulator Hose Assembly from Manifold Connection. Save removed LP Manifold Conn
Connecting Your Grill to the Natural Gas Source. 1. A professionally-installed shut-off valve between the supply piping and the socket is recommended,
DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.EmergenciesProblemGas leaking from cracked/cut/
Troubleshooting (continued)ProblemBurner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also)Burner(s) will notmatch light.
Troubleshooting - Electronic IgnitionProblem (Ignition)SECTION INo sparks appear at any electrodes when Electronic Ignition Buttonis pressed; no noise
39 First Name | Nombre | Prénom Initial | Inicial | Initiale Last Name | Apellido | Nom de FamillieAddress (number & street) | Dirección (número
• NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full.• An over filled or impr
WARNINGIf “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department!Connecting Regulator to the
6.Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in
7Safety Tips Before opening LP cylinder valve, check the coupling nut for tightness. When grill is not in use, turn off all control knobs and LP cyl
8Ignitor Check•Turn gas off at LP cylinder. Press and hold electronic ignitor button. "Click" should be heard and spark seen each time betw
9 CAUTION•Clean cooking grates.•Store in dry location.•When LP cylinder is connected to grill, store outdoors in a well-ventilated space and out of r
Comments to this Manuals