Char-Broil 4984619 User's Guide

Assembly instructions © 2013 PRODUCT GUIDEMODEL 463240613© 2013 Char-Broil, LLC Columbus, GA 31902Printed in China Serial NumberDate Purchase

VERY IMPORTANT: Burner venturi must be attached with orificeholder properly. see illustration below.We suggest three ways to clean the burner tubes. U

NOTES 11

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this pr

PARTS LISTNOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the

ABCDEFGHIJKLMNOPQRTUVWXYZAABBCCSPARTS DIAGRAM14

12Bottom shelfNon-locking caster (Front)Locking caster (Rear)RearFrontLeft side panelRight side panelMagnetFrontCaster pinAPlace bottom shelf upside d

3Grill headCartIgnitor wireRegulatorThis step requires two people to lift and position stove top onto cart. Carefully lower the stove top onto the

5Back panel6On back of the stove top, attach back panel to cart side panels using four #8x3/8" self-tapping screws.Connect the wire from burner e

7Attach tank exclusion wire to back panel and front brace using two #8-32x3/8" screws and #8-32 nuts.Back panelFront braceTank exclusion wire#8-3

109Front braceBottom shelfHinge pin on bottom of doorTop of doorPRESSInsert hinge pin on bottom of door into hole in bottom shelf. Press upper hinge p

TABLE OF CONTENTS1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.2. An LP cylinder

LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder h

1Main Burner ConversionYour grill may differ from illustration shown. This portion of the manual covers a variety of grill styles. Use pictures as r

NOTE: Reinstall Screws4Pull the Burner Control Knob off of Valve Stem.Remove Screws and Washers that secure the Bezel to the Control Panel. Save remo

6Natural Gas Hose Conversion LP Regulator Hose AssemblyManifold ConnectionNatural Gas Hose AssemblyManifold ConnectionUsing a wrench, not provided, re

Connecting Your Grill to the Natural Gas Source.and the socket is recommended, but not required, by the National Fuel Gas Code. Socket connection must

DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.EmergenciesProblemGas leaking from cracked/cut/

Troubleshooting (continued)ProblemBurner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also)Burner(s) will notmatch light.

Troubleshooting - Electronic IgnitionProblem (Ignition)SECTION INo sparks appear at any electrodes when Electronic Ignition Buttonis pressed; no noise

NOTES 28

NOTES29

WARNINGInstallation Safety Precautions• Use grill, as purchased, only with LP (propane) gas and the regulator/valve assembly supplied. If your grill i

NOTES 30

*❶ First Name | Nombre | Prénom Initial | Inicial | Initiale Last Name | Apellido | Nom de Famillie Address (number & street) | Dirección (núm

THANK YOU FOR YOUR RECENT PURCHASE FROM REGISTER YOUR PRODUCT TO RECEIVE A SPECIAL OFFERCHARBROIL.COM/REGISTERCHECK OUT THESEGREAT FEATURESON OUR WEB

• NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full.• An over filled or impr

WARNINGIf “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department!Connecting Regulator to the

6.Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in

7WARNINGFor Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free fro

8CAUTIONIf ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does no

9• Plastic parts: Wash with warm soapy water and wipe dry.▲ Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on pla